Why Are My Grandfather Clock Weights Stuck?
Clock Weights Not Dropping? Here’s Why.
If the weights on your grandfather clock are stuck and no longer drop, your clock will eventually stop ticking, chiming, or striking. This is one of the most common problems owners face with mechanical clocks, especially weight-driven grandfather clocks. Fortunately, you can usually solve the issue with a bit of knowledge and troubleshooting.
In this article, we explain why grandfather clock weights get stuck, how to diagnose the cause, and what steps to take to safely correct the problem—without damaging your clock. Whether you’re a first-time clock owner or a seasoned enthusiast, this guide will help you restore proper function and avoid costly mistakes.
What Do the Weights on a Grandfather Clock Do?
Grandfather clocks use weights to power the internal movement. Most mechanical grandfather clocks have three weights:
- Left weight: Powers the hour strike
- Center weight: Runs the timekeeping gear train
- Right weight: Powers the chime (Westminster or other melodies)
Each weight is suspended by either a cable or chain, and it slowly drops over the course of seven to eight days. As the weights drop, they transfer energy through the clock’s gearing system to keep the clock running, chiming, and striking. When the weights stop descending, something is interfering with the clock’s function.
Why Do Grandfather Clock Weights Get Stuck?
If one or more weights stop moving, it usually means the clock is no longer running properly. Here are the most common reasons:
1. The Clock Has Stopped Running
If the center weight (time train) is stuck, the movement itself may have stopped due to dirt, wear, or incorrect setup. When the clock stops ticking, the weight won’t drop.
2. Cables or Chains Are Jammed
Kinks or misalignment in the cables or chains can cause the weights to hang mid-air. This can happen if the cables wind unevenly on the drum or get tangled during winding.
3. Incorrect Weight Placement
Each weight must go in the correct position. If you move them around during setup or maintenance and place them in the wrong order, the clock may not have enough power to run each function, causing a weight to stop dropping.
4. The Movement Needs Cleaning or Oil
Dry bushings or worn pivots can create so much resistance that the weight cannot drive the gears. If your clock hasn’t been serviced in over 10 years, buildup and friction may be to blame.
5. Safety Mechanisms Engaged
Some clocks have internal safety stops that prevent overwinding. If one becomes jammed or misaligned, the weight may get locked in place.
6. Pendulum Not Engaged
If the pendulum is not swinging or hasn’t been properly restarted after winding, the clock may look intact—but the time train won’t run, and the weights won’t move.
How Do I Fix Stuck Grandfather Clock Weights?
Start by identifying which weight is stuck, then follow these steps:
Step 1: Check the Clock Movement
- Open the hood and observe whether the pendulum is swinging.
- If the pendulum is not in motion, try gently starting it.
- Listen for the tick-tock sound. If it’s not consistent or stops, the clock isn’t running.
Step 2: Confirm Weight Placement
- Check the bottom of each weight. Some are marked with “L” (left), “C” (center), or “R” (right).
- Make sure the heaviest weight is in the correct spot—typically the chime (right side).
- Reposition the weights if needed.
Step 3: Inspect the Cables or Chains
- Shine a flashlight into the weight pulley or chain sprocket area.
- Look for kinks, twists, or tangled cords.
- If you spot a tangle, support the weight from below, unwind the chain or cable, and reset it properly.
Step 4: Manually Advance the Movement
- Gently move the minute hand forward to trigger the next chime or strike sequence.
- If the movement resumes, the problem was likely a temporary jam in the chime or strike train.
Step 5: Lightly Lubricate the Movement (If Qualified)
- Use only clock-grade oil and apply sparingly to pivots and bushings.
- Never spray WD-40 or household lubricants—they cause long-term damage.
Step 6: Reset the Cables or Chains
- If cables have overwound or jumped the drum, the weight will not descend.
- Resetting requires removing the dial and rethreading the cable properly on the drum—this is best done with professional guidance.
When Should I Replace Parts?
If you’ve already tried the above and your weights remain stuck, some components may be worn out. Over time, clock movements wear down and require full replacement—especially after 20–30 years of operation.
You should consider replacing the movement if:
- Weights consistently stick even after resetting
- Bushings are visibly worn or oval-shaped
- Chimes and strikes are out of sync or weak
- The clock has not been serviced in decades
At Clockworks, we offer factory-fresh Hermle, Kieninger, and Urgos movements for nearly all grandfather clock brands, plus full repair and cleaning services if you prefer to keep the original movement.
Can I Still Wind a Clock with a Stuck Weight?
You should not attempt to forcefully wind a clock with a stuck weight. Doing so may:
- Damage the cable or chain
- Break a pulley
- Snap the movement drum
- Create irreversible damage to the gearing system
Instead, stabilize the weight and follow the diagnostic steps above to identify the issue. If needed, remove the weight and inspect the movement with the power load removed.
How Can I Prevent Weights from Getting Stuck Again?
Regular maintenance is key. Follow these tips to keep your grandfather clock running smoothly:
- Wind the clock at the same time each week
- Keep the clock level and stable
- Avoid moving the weights or pendulum without support
- Have the movement cleaned and oiled every 7–10 years
- Don’t use household oil or sprays
Conclusion
Stuck grandfather clock weights are usually a symptom—not the root problem. Whether it’s tangled cables, incorrect weight placement, or a worn-out movement, you can often fix the issue with careful inspection and the right tools. Never force a weight to move—doing so can cause costly damage.
At clockworks.com, we help customers every day with stuck weights, broken movements, and everything in between. Email us at clockworks@clockworks.com for expert guidance and trusted replacement parts.
Updated on: 04/10/2025
Thank you!