Why Does My Clock Chime at the Wrong Time?

How a Clock Ends Up Chiming at the Wrong Time

When a clock chimes at the wrong hour or plays its melody out of sync, it throws off the entire rhythm of your space—not to mention your sense of time. This issue frustrates many clock owners, especially when the clock seems to run and tick just fine otherwise. The good news is that most chime problems stem from a few common causes, and you can fix them without replacing the movement.

In this guide, we’ll explain why clocks chime at the wrong time and walk you through how to reset the chime mechanism or realign the hands, depending on your clock type.

When a clock’s chimes no longer match the time on the dial, the issue almost always falls into one of these categories:

1. Hour hand is out of sync with the strike count.
2. Minute hand is in the wrong position on the shaft.
3. Chime train got interrupted or skipped sequence.
4. Incorrect manual movement of hands—turning them backward or too fast.
5. Power failure on a quartz chiming clock leading to drift.

Mechanical clocks (such as Hermle, Kieninger, or Seth Thomas movements) require proper alignment of the hands and chime levers. Quartz Chime Clocks rely on internal programming, so their reset process differs.

How Do I Fix a Mechanical Clock That Chimes Incorrectly?

Step 1: Let the Clock Run and Observe

Allow the clock to chime at the top of the hour. Note what hour it chimes and what the hands say. For example, if the hands show 3:00 but it strikes 5 times, the hour hand is out of sync.

Step 2: Move the Hour Hand to Match the Chime

Do not move the minute hand yet. Instead, gently move the hour hand (the shorter one) to point at the number that matches the number of chimes. The hour hand is friction-fit and should slide without resistance.

Example: If it chimes five times at 3:00, move the hour hand to point at 5.

Step 3: Reset the Time Using the Minute Hand

Now, advance the minute hand (the longer one) clockwise, stopping at each quarter hour to let the clock complete its chime cycle. Never skip chime points or move the hand backward—this can damage the movement.

Advance the minute hand until the correct time is displayed. Your clock should now chime in sync.

What If the Minute Hand Is the Problem?

In some cases, the minute hand points to the wrong spot when the chime sounds. If the chime occurs at, say, 10 minutes past the hour instead of on the hour, the minute hand is incorrectly positioned on the shaft.

How to Fix It:

1. Wait for the next full-hour chime.
2. Gently remove the minute hand using a small wrench or hand puller.
3. Reposition the hand to point exactly at 12.
4. Reattach and secure it, then test the timing.

Some clocks use a square hole on the minute hand to align with a square shaft. Make sure the hand sits straight and tight before reattaching the nut.

How Do I Fix a Quartz Chiming Clock?

Quartz clocks with chiming features often lose sync after a battery change or power outage. Most have a button or switch labeled “RESET” or “CHIME SYNC.”

To resync:

1. Replace batteries with fresh ones.
2. Set the hands to the current time using the setting knob.
3. Use the reset button to cycle through the chime sequences until the clock chimes match the current hour.

Each manufacturer has slightly different steps, so check the manual if available.

Should I Ever Move the Hands Backward?

No. Most mechanical chiming clocks can’t tolerate backward hand movement. Doing so may jam or misalign the chime and strike sequences. Always move the minute hand clockwise only, pausing to let the clock complete its chime or strike at each point.

The only exception is some high-end modern movements with auto-correct features, but even those work better with clockwise setting.

What If My Clock Still Won’t Sync?

If you’ve followed all the steps above and your clock still chimes off-schedule, one of the following may apply:

• The movement is worn out or damaged. Worn cams, bent levers, or slack in the gear train can cause chime drift.
• A previous owner forced the hands backward or misaligned the chime assembly.
• Incorrect installation of a new movement (especially if using a replacement quartz unit).

In these cases, a deeper repair or full movement replacement may be needed. If you’re unsure which movement you have, or if you need help selecting a replacement, professional support can save you time and frustration.

What Are Common Clock Types That Experience Chime Issues?

• Mantel/Wall clocks with Westminster or Whittington chimes
• Grandfather clocks with triple-chime movements
• Anniversary clocks with hourly strike features

Each has its own sequence and gear configuration, so the repair method may vary slightly.

Final Tips for Chime Troubleshooting

• Always let the chimes finish before adjusting anything.
• Use the correct tools when removing or tightening hands.
• Keep track of how many times the clock strikes and when.
• Take pictures before removing any hands or nuts.
• Avoid winding or adjusting the clock during chime sequences.

If your clock continues to chime at the wrong time despite your efforts, Clockworks can help. We carry a full range of chiming clock movements and offer expert repair guidance. Visit https://www.clockworks.com or email clockworks@clockworks.com for personalized assistance.

Updated on: 12/07/2025